Unaligned – The Archivist
This datasheet does not meet the selection criteria (see Settings tab).
5

The Archivist

NoNAME  M WS BS S T W A Ld Sv Base
90
The Archivist (base: 50mm)
1
90
The Archivist
5" 3+ 3+ 5 4 6 4 9 3+ 50mm
The Archivist is a single model equipped with: atomic disassembler, eradicator glove. You can only include one of this model in your army.
WEAPON
RANGE
TYPE
S
AP
D
ABILITIES 
Atomic disassembler
Atomic disassembler
18"
Pistol 1
8
-3
D6
When resolving an attack made with this weapon the target does not receive the benefit of cover to its saving throw.
When resolving an attack made with this weapon the target does not receive the benefit of cover to its saving throw.
Eradicator glove
Eradicator glove
Melee
Melee
x2
-3
3
When resolving an attack made with this weapon, subtract 1 from the hit roll.
When resolving an attack made with this weapon, subtract 1 from the hit roll.
ABILITIES
ABILITIES
Disruptive Influence: Subtract 1 from the Leadership characteristic of enemy and friendly units whilst they are within 3" of any model with this ability.
FACTION KEYWORDS: UNALIGNED, ZOAT
KEYWORDS: CHARACTER, MONSTER, THE ARCHIVIST
Faction Rules
Hit Roll
When a model makes an attack, make one hit roll for that attack by rolling one D6. If the result of the hit roll is equal to or greater than the attacking model’s Ballistic Skill (BS) characteristic (if the attack is being made with a ranged weapon) or its Weapon Skill (WS) characteristic (if the attack is being made with a melee weapon), then that attack scores one hit against the target unit. If not, the attack fails and the attack sequence ends.

If an attack is made with a weapon that has an ability that says it ‘automatically hits the target’, no hit roll is made – that attack simply scores one hit on the target unit. An unmodified hit roll of 6 always scores a hit, and an unmodified hit roll of 1 always fails. A hit roll can never be modified by more than -1 or +1. This means that if, after all the cumulative modifiers to a hit roll have been calculated, the total modifier would be -2 or worse, it is changed to be -1. Similarly, if, after all the cumulative modifiers to a hit roll have been calculated, the total modifier would be +2 or better, it is changed to be +1.
Saving Throw
The player commanding the target unit then makes one saving throw by rolling one D6 and modifying the roll by the Armour Penetration (AP) characteristic of the weapon that the attack was made with. For example, if the weapon has an AP of -1, then 1 is subtracted from the saving throw roll. If the result is equal to, or greater than, the Save (Sv) characteristic of the model the attack was allocated to, then the saving throw is successful and the attack sequence ends. If the result is less than the model’s Save characteristic, then the saving throw fails and the model suffers damage. An unmodified roll of 1 always fails.
PISTOL
Due to their compact size, pistols can even be used in melee to shoot at point-blank range.
A model can make attacks with a Pistol even when its unit is within Engagement Range of enemy units, but it must target an enemy unit that is within Engagement Range of its own unit when it does so. In such circumstances, the model can target an enemy unit even if other friendly units are within Engagement Range of the same enemy unit.

When a model equipped with both a Pistol and another type of ranged weapon (e.g. a Pistol and a Rapid Fire weapon) shoots, it can either shoot with its Pistol(s) or with its other ranged weapons. Choose which it will fire (Pistols or non-Pistols) before selecting targets.

  • Can be shot even if firing model’s unit is within Engagement Range of enemy unit.
  • Cannot be shot alongside any other type of weapon.

This datasheet has Elites Battlefield Role. Full list of Unaligned units sharing same Battlefield Role follows:

Select Weapon
When a model makes a close combat attack, it must do so using a melee weapon (i.e. a weapon that has the ‘Melee’ type). The weapons a model is equipped with are described on its datasheet. If a model is not equipped with any melee weapons, or if it cannot make an attack with any of the melee weapons it is equipped with, then that model makes its attacks using a close combat weapon, which has the following profile:

WEAPONRANGETYPESAPD
Close combat weaponMeleeMeleeUser01

If a model has more than one melee weapon, select which it will use before resolving any attacks. If a model has more than one melee weapon and can make several attacks, it can split them between these weapons however you wish – declare which attacks are being made with which weapons before any attacks are resolved. If the selected weapon has more than one profile that you must choose between, you must declare which profile is being used at the same time. Different attacks made with such a weapon can be made using different profiles if you wish.

If your unit is making attacks with more than one melee weapon against a unit, and those weapons have different characteristics profiles, then after you have resolved an attack with one of those weapons you must, if any other weapons with the same characteristics profile are also being used to make attacks against that unit, resolve those attacks before resolving any attacks against the target with a weapon that has a different characteristics profile. Note that all the attacks you have declared are always resolved against the target unit even if, when you come to resolve an individual attack, no models in the target unit remain in range (this can happen because of models being destroyed and removed from the battlefield as the result of resolving other attacks made by the attacking model’s unit first).

  • Each close combat attack is made with a melee weapon.
  • A model makes attacks using the close combat weapon profile if it has no other melee weapons.
  • If a unit attacks with multiple weapons, all attacks made with weapons that have the same profile must be resolved before resolving attacks with the next.

The MONSTER keyword is used in the following Unaligned datasheets:

Terrain and Cover
Some pieces of terrain can provide certain bonuses to units in your army. Each bonus and how to acquire it is described in the Terrain Features section of the Core Rules. If a model has acquired such a bonus (to it's Save, Leadership or other characteristics), it is considered as receiving the benefit of cover. There are ways for some models to ignore such bonuses while making an attack, but it should be known what kind of benefit is ignored (see the Rare Rules for clarification).
© Vyacheslav Maltsev 2013-2021